상품상세정보

Description

Feather is the new development board from Adafruit and like its namesake it is thin light and lets you fly! We designed Feather to be a new standard for portable microcontroller cores. This is theAdafruit Feather M0 WiFiw/ATWINC1500 - our take on an 'all-in-one' Arduino-compatible + high speed reliable WiFi with built in USB and battery charging. Its an Adafruit Feather M0with a WiFi module ready to rock!We have other boards in the Feather family check'em out here.

Connect your Feather to the Internet with this fine new FCC-certified WiFi module from Atmel. This 802.11bgn-capable WiFi module is the best new thing for networking your devices with built-in low-power management capabilites Soft-AP SSL TSL 1.2 support and rock solid performance. We were running our adafruit.io MQTT demo for a full weekend straight with no hiccups (it would have run longer but we had to go to work so we unplugged it). This module is very fast & easy to use in comparison to other WiFi modules we've used in the past.

This module works with 802.11b g or n networks & supports WEP WPA and WPA2 encryption. You can connect to your own WiFi networks or create your own with "Soft AP" mode where it becomes its own access point (we have an example of it creating a webserver that you can then control the Arduino's pins).You can clock it as fast as 12MHz for speedy reliable packet streaming. And scanning/connecting to networks is very fast just a second or two.

You might be wonderingwhy use thiswhen you can get a HUZZAH Feather?Well you get:

• A highly-capable Cortex M0+ processor with ton more I/O pins lots of 12-bit ADCs a 10-bit DAC 6 total SERCOMs that can each do SPI I2CorUART (3 are used by the existing interfaces leaving you 3) plenty of timers PWMs DMA native USB and more (check out the Datasheet)
• The ATWINC has much lower power usage about 12mA for the WINC & 10mA for the ATSAMD21 with auto-powermanagement on for the WiFi and no power management for the ARM. With manual power management you can get the WiFi module to down to ~2mA by putting it to sleep.
• This is compared to the ESP's ~70mA average current draw and whose deep sleep mode requires a WDT reset.
• We also found that we could stream more reliably (less 'bursty') with the ATWINC although altogether the ESP has higher throughput.
• You also dont have to 'yield' all the time to the WiFi core since its a separate chip. You get full reign of the processor and timing

Of course both WiFi-capable Feathers have their strengths and tradeoffs & we love both equally!

At the Feather M0's heart is an ATSAMD21G18 ARM Cortex M0 processor clocked at 48 MHz and at 3.3V logic the same one used in the newArduino Zero. This chip has a whopping 256K of FLASH (8x more than the Atmega328 or 32u4) and 32K of RAM (16x as much)! This chip comes with built in USB so it has USB-to-Serial program & debug capability built in with no need for an FTDI-like chip. For advanced users who are comfortable with ASF the SWDIO/SWCLK pins are available on the bottom and when connected to a CMSIS-DAP debugger can be used to use Atmel Studio for debugging.

To make it easy to use for portable projects we added a connector for any of our 3.7V Lithium polymer batteries and built in battery charging. You don't need to use a battery it will run just fine straight from the micro USB connector. But if you do have a battery you can take it on the go then plug in the USB to recharge. The Feather will automatically switch over to USB power when its available. We also tied the battery through a divider to an analog pin so you can measure and monitor the battery voltage to detect when you need a recharge.

Here's some handy specs! Like all Feather M0's you get:

• Measures 2.1" x 0.9" x 0.3" (53.65mm x 23mm x 8mm) without headers soldered in. Note it is 0.1" longer than most Feathers
• Light as a (large?) feather - 6.1 grams
• ATSAMD21G18 @ 48MHz with 3.3V logic/power
• 256KB FLASH 32KB SRAM No EEPROM
• 3.3V regulator (AP2112K-3.3) with 600mA peak current output WiFi can draw 300mA peak during xmit
• USB native support comes with USB bootloader and serial port debugging
• You also get tons of pins - 20 GPIO pins
• Hardware Serial hardware I2C hardware SPI support
• 8 x PWM pins
• 10 x analog inputs
• 1 x analog output
• Built in 200mA lipoly charger with charging status indicator LED
• Pin #13 red LED for general purpose blinking
• Power/enable pin
• 4 mounting holes
• Reset button

Comes fully assembled and tested with a USB bootloader that lets you quickly use it with the Arduino IDE. We also toss in some header so you can solder it in and plug into a solderless breadboard.Lipoly batteryandMicroUSB cablenot included(but we do have lots of options in the shop if you'd like!)

Check out our tutorial for all sorts of details including pinouts power management Arduino IDE setup and more!

Technical Details

Learn

Using ATSAMD21 SERCOM for more SPI I2C and Serial ports

Get more high speed serial commports without bitbanging

LIGHTSHIP: LED Animation over WiFi

Any sufficiently advanced technology is indistinguishable from magic.

Adafruit Feather M0 WiFi with ATWINC1500

ARM Cortex M0+ with fast & fun wireless built in

Proper Debugging of ATSAMD21 Processors

Step in step out step over and repeat!

Automatic Twitch On-Air Sign

Know when your favorite streamer is twitchin'

Pixie CyberWig - A Wearable WiFi LED Visualization

Wireless video on your head

3D Printed IoT On Air Sign for Twitch

Make an internet connected On Air Sign

7 Segment Display Internet Clock

NTP-enabled clock in your favorite color

상품결제정보

* 세금계산서 발행방법은 게시판 공지사항 참조.
* 기술문의는 이메일(master@toolparts.co.kr)로 문의.

전자부품 특성상 제품에 이상이 있거나, 상품정보와 상이한 경우 외 에 단순 고객변심으로는
교환 반품이 불가능 합니다 구매전 이점 유의해 주세요!!!

고액결제의 경우 안전을 위해 카드사에서 확인전화를 드릴 수도 있습니다. 확인과정에서 도난 카드의 사용이나 타인 명의의 주문등 정상적인 주문이 아니라고 판단될 경우 임의로 주문을 보류 또는 취소할 수 있습니다.  

무통장 입금은 상품 구매 대금은 PC뱅킹, 인터넷뱅킹, 텔레뱅킹 혹은 가까운 은행에서 직접 입금하시면 됩니다.  
주문시 입력한 입금자명과 실제입금자의 성명이 반드시 일치하여야 하며, 7일 이내로 입금을 하셔야 하며 입금되지 않은 주문은 자동취소 됩니다.

배송정보

• 배송 방법 : 택배
• 배송 지역 : 전국지역
• 배송 비용 : 3,000원
• 배송 기간 : 1일 ~ 3일
• 배송 안내 : 산간벽지나 도서지방은 별도의 추가금액을 지불하셔야 하는 경우가 있습니다.
  주문하신 제품은 입금확인후 1~3일 내에 출고되며 (해외배송)으로 표시된 제품은
  해외배송 제품으로 배송기간이 약 10일~14일정도 소요될수 있습니다.
  구매전 해외배송 제품은 배송기간을 꼭 확인해 주세요.
  해외배송 진행하신상품은 반품 불가능 합니다.

교환 및 반품정보

교환 및 반품이 가능한 경우
- 상품을 공급 받으신 날로부터 7일이내 단, 가전제품의
  경우 포장을 개봉하였거나 포장이 훼손되어 상품가치가 상실된 경우에는 교환/반품이 불가능합니다.
- 공급받으신 상품 및 용역의 내용이 표시.광고 내용과
  다르거나 다르게 이행된 경우에는 공급받은 날로부터 3월이내, 그사실을 알게 된 날로부터 30일이내

교환 및 반품이 불가능한 경우
- 고객님의 책임 있는 사유로 상품등이 멸실 또는 훼손된 경우. 단, 상품의 내용을 확인하기 위하여
  포장 등을 훼손한 경우는 제외
- 포장을 개봉하였거나 포장이 훼손되어 상품가치가 상실된 경우
  (예 : 가전제품, 식품, 음반 등, 단 액정화면이 부착된 노트북, LCD모니터, 디지털 카메라 등의 불량화소에
  따른 반품/교환은 제조사 기준에 따릅니다.)
- 고객님의 사용 또는 일부 소비에 의하여 상품의 가치가 현저히 감소한 경우 단, 화장품등의 경우 시용제품을
  제공한 경우에 한 합니다.
- 시간의 경과에 의하여 재판매가 곤란할 정도로 상품등의 가치가 현저히 감소한 경우
- 복제가 가능한 상품등의 포장을 훼손한 경우
  (자세한 내용은 고객만족센터 1:1 E-MAIL상담을 이용해 주시기 바랍니다.)

※ 고객님의 마음이 바뀌어 교환, 반품을 하실 경우 상품반송 비용은 고객님께서 부담하셔야 합니다.
  (색상 교환, 사이즈 교환 등 포함)

서비스문의